Connectivity

HDMI Ports: 3 x HDMI 2.1 (HDMI 1 supports eARC, HDMI 2 recommended for gaming, all support CEC)

USB: USB-A x 1, Micro-USB Connector x 1

Audio Out: Line out x 1

Digital Audio Output: S/PDIF x 1

Ethernet: RJ45 x 1

TV Stick Compartment: 1

Wi-Fi: Wi-Fi 6

Bluetooth: 5.2

Screen Cast: Yes

Backlit Remote: IR & Bluetooth Dual Mode

Power

Power Supply (AC): 100-240V ~ @50/60Hz

Power Supply (DC): 24V ⎓ 12.5A

Power Consumption: 300W

Standby Mode: ≤0.5W

General

Dimensions: 11.06 x 9.33 x 9.13 IN, 28.1 x 23.7 x 23.2 CM

Weight: 11.46 LB / 5.2 KG

Working Temperature: 32~95°F / 0-35℃

Storage Temperature: -4~131°F / -20~55℃

Operating Humidity: 30%~85%

Product Notes:

• 1. The listed 2600 ANSI Lumens, tested by NexiGo Lab, represent the projector's highest brightness, which may vary due to test conditions and unit variations.
• 2. For the best viewing experience, we recommend using a projection size of 80-150 inches. Exceeding this range may affect the quality of your projected content. The display quality may vary based on product usage habits and environmental conditions.
• 3. The 4.2ms input lag was tested under 1080p@240hz in low latency mode. The data comes from the NexiGo lab. Results may vary based on different testing environments, conditions, and the product being evaluated.
• 4. The light source's theoretical lifespan is 25,000 hours, though actual lifespan may differ based on environmental conditions, usage habits, and the selected mode.
• 5. Measured under an ambient temperature of 25°C with a 1-meter distance from the machine. Results may vary based on different testing environments, conditions, and the product being evaluated. This data comes from the NexiGo lab.

Frequency Asked Questions

How do I pair the remote with NexiGo TriVision Ultra？

Infrared(IR) Pairing：

Point the remote control towards the IR sensor on the back of the projector. The angle of the remote control should not must be within ± 15 degrees of the projector's IR sensor and the distance between the remote control and the sensor(s) should not exceed 26 feet (~ 8 meters).

Bluetooth Pairing (Recommended)：

Enable Bluetooth on your TriVision Ultra by going to Settings > Bluetooth Connection > Bluetooth > On. 

Please hold the remote within 7.87 inches of the projector. Point it towards the projector and press and hold the Return and Menu buttons simultaneously for at least 10 seconds to put the remote control into pairing mode. lf the pairing is successful, the screen will display the message, "Bluetooth remote control is paired".

Note:

• If the Bluetooth connection is disabled, you will need to re-pair the remote in order to continue using it via Bluetooth.
• Do not place objects in front of the projector's IR sensor. This may prevent the sensor from operating properly.
• The IR sensor on the remote, like all IR sensors, can be interfered with by extremely bright light sources. If the remote is not working properly, make sure that there are no bright lights shining on them.

What formats of 3D video does TriVision Ultra support?

The projector supports 3D Frame Sequential, Frame Packing, Side by Side 3D, and Top & Bottom 3D. To watch 3D movies, you will need a pair of 120Hz active shutter 3D glasses.

Note: 3D Frame Sequential and Frame Packing are only available by HDMI connection.

How to connect a soundbar or speaker to the TriVision Ultra?

To connect a soundbar or speaker, you can use one of the methods below, depending on the connection options available on your soundbar.

Option 1: HDMI eARC or ARC (Recommended)

Connect your soundbar or speaker to the HDMI 1 port on the TriVision Ultra using an HDMI cable. Then, go to Settings > Audio Settings > Sound Output Source and select HDMI eARC. For an HDMI ARC compatible soundbar or speaker, you will also need to switch the ARC option to On. This ensures that audio is sent from the projector to the soundbar via HDMl with enhanced capabilities.

Option 2: Optical

Connect your soundbar or speaker to the S/PDIF port on the projector using an optical cable. Then, go to Settings > Audio Settings > Sound Output Source and select S/PDIF.

Option 3: Bluetooth

Enable Bluetooth on your soundbar or speaker and on the TriVision Ultra. On your projector, go to Settings > Bluetooth Connection > Output, then scroll down to Search Device and choose your soundbar from the list of available devices.

Why is no sound from TriVision Ultra?

If there is no sound coming from TriVision Ultra, you may have selected a different audio output source. Go to Settings > Audio Settings > Sound Output Source and select the Internal Speakers to switch the audio output back to the TriVision Ultra.

Have Any Other Questions?

 Feel free to leave your questions to us. We will reply you asap!